Skip to main content

adsense

BALLON LAMP!!!AMEZING!!! (simple Awsome Ballon Lamp)!!

The simple ballon lamp is made from the ballons and the 12v led strip with the led driver

Step 1: WATCH THE VIDEO

 


After watching the video follow the steps as

Step 2: THINGS NEEDED

     
     

TO MAKE THE BALLON YOU NEED THE FOLLOWING THINGS
1.BALLON
2.GLUE
3.THREAD
4.12V LED STRIP
5.12V LED STRIP CONTROLLER
6.STICKING TAPE
7.POWER SUPPLY 12V

Step 3: PROCEDURE OF MAKING

     
     

making the glue ready to do this take the glue in a empty box and mix it with 1/3 part of water and them shake well and make sure the glue is mixed well in the water
the if you want you can add some colour in the solution and make it colourfull
after that is done you need to follow the instructions for winding the thread on the ballon as i have showen in the following video
let it dry for some 12-15 hours then by using a sharp pin pinch in the ballon and after the ballon blsast you are with an awsome looking mold of the ballon

Step 4: ADDING THE GLOW !!!!!!!

MJJC-12VDC-New-SMD5025-Color-temperature-led-strip-light-Non-waterproof.jpg

now its time to add the glow to the ballon skeleton
i thought of adding a 12v led strip insted of the regular bulb because the regular bulb gets heated very soon and consume a lot of power.
there is nothing much to explain about the 12v strip and the driver connection because nowadays the come in a direct pair as in the diagram
12v led strip driver
+12v pin----------------------+12v of driver
RED---------------------------RED
BLUE--------------------------BLUE
GREEN-----------------------GREEN

Step 5: THANKS FOR WATCHING

THANKS FOR WATCHING THE PROJECT
YOU CAN VISIT MY YOUTUBE CHANNEL

https://www.youtube.com/channel/UCZE35bOktFxu8dIadxuQPLg

I POST THE VIDEOS EVERY WEEK ABOUT THE ARDUINO,BLUETOOTH MODULE,WIFI MODULE ,INFRA RED
AND MANY MORE
THANKS FOR THE SUPPORT

 

 


 

 

Comments

Post a Comment

Popular posts from this blog

VU METER (Music Visualizer) #1 With Arduino

This is the part one of the music visualizer series and In the following tutorial we are going to make a music visualizer AKA the volume meter or the uv meter from an arduino mega . The build process is very simple and easy and the program of arduino is also not that hard. Step 1: Watch the Video Step 2: Parts List             The parts needed for this build are 1.ARDUINO MEGA 2.COPPER DOT PCB 3.BREAD BOARD 4.JUMPER WIRES 5.LED (RED ,BLUE ,GREEN) 6.TOOLS(SOLDERING IRON ,SOLDER WIRE) 7.AUDIO SPLITER WITH A JACK 8.HEADER PINS Step 3: Testing on Bread Board( 1.LED's and ARDUINO ) Start by inserting the led on the bread board with the negative leg of the led to a common ground rail of the bread board (led count =20) the positive leg of the led will be there at any empty rail of the bread board as shown in the video and following pictures Then connect the ground of the arduino to the common ground rail of the l...
Post a Comment
Read more

ARDUINO IR REMOTE (USE YOUR OLD REMOTE TO CONTROLL HOME APPLIANCES)

In this project you can choose any remote or a TV remote which you are using and you will notice that some keys are useless for your tv for that you can use that keys for controlling the home appliences like powering your TV,FAN,LIGHTS etc... you need to follow the simple procedure from the video so that you can record hexa values for that particular key and put into the program of the arduino Step 1: WATCH THE VIDEO   Step 2: THINGS NEEDED           The things needed for the following project are 1.ARDUINO UNO OR CLONE 2.IR RECIVER 3.ANY OLD REMOTE 4.RELAY MODULE 5.JUMPER WIRES 6.ARDUINO IDE 7.SOME LED'S IF YOU WANT TO MAKE A RELAY MODULE BY YOURSELF YOU COULD NEED (OPTIONAL) 1.RELAY 2.BC547 TRANSISTOR 3. 1K OHM RESISTOR 4.COPPER DOT PCB Step 3: RECIVING THE IR CODE FROM REMOTE BUTTON   This is the test to recieve the hexadecimal code of the remote button 1.install the ir remote library form the fo...
Post a Comment
Read more

VU METER (Part-2) Using LM-3914 & LM-3915

This is the second part of the music visualization series and in the video above i have shown how you can make a simple VU meter by using the ic called LM-3914 or LM-3915. The part 1 is basically about how you can make the simple and cool looking VU meter by using the arduino microcontroller link to that is given as and now we will see the step by step construction of the VU meter STEP 1: Watch the Video   STEP 2: PARTS LIST     To make this cool looking UV meter we need these following things 1.LM-3914 IC 2.Breadboard 3.Copper dot PCB 4.18 pin IC Holder 5.Resistor(1.2k & 4k ohm) 6.Potentiometer (1K ohm) & Knob 7.Audio jack 8.Dc jack 9.LED (6-Green & 2-Blue & 2-Red) 10.some connecting wires   TOOLS REQUIRED 1.soldering iron 2.wire cutter 3.soldering wire etc... STEP 3: SPECIFICATION OF LM-3914 & DATASHEET When looking at the LM-3914 ic datasheet these are some important feat...
Post a Comment
Read more